How to Install a Saris Bike Rack on an SUV
To install a Saris bike rack on an SUV, first confirm your SUV's fit, then either strap a trunk rack over the rear hatch or slide a hitch rack into the receiver. Tighten every connection, load the bikes, and check the rack again before you drive.
On this page (8 sections)
- Does a Saris rack fit your SUV?
- How do you prepare the SUV before mounting the rack?
- How do you install a Saris trunk rack on an SUV?
- How do you install a Saris hitch rack on an SUV?
- How tight should the straps and hitch hardware be?
- How do you test the rack before driving?
- How do you remove and store a Saris SUV rack?
- What should you check before you drive off?
To install a Saris bike rack on an SUV, check the fit first, then mount it by the style you bought: a trunk rack straps over the rear hatch, while a hitch rack slides into a receiver. Tighten every strap or pin, load the bikes, and recheck the whole setup before you pull away.
The whole job takes about 15 to 30 minutes once you have the right rack and a clean SUV.
Does a Saris rack fit your SUV?
Confirm fit before you install anything, because not every Saris rack suits every SUV. Saris makes trunk racks and hitch racks, and each has its own compatibility rules.
For a trunk rack, Saris offers a QR code on the packaging that checks your vehicle model before you buy. For a hitch rack, you match the rack to your receiver size and class.
Most SUVs sold in the US carry a 1 1/4-inch or 2-inch receiver, and the rack's drawbar must match it. Measure the receiver opening and read the rack's spec sheet rather than guessing.
If you are still choosing between styles, our guide to the types of hitch bike racks explains hanging, platform and tilt designs. A bike rack for SUV buyers often start with is a hitch model, but a trunk rack works well on many hatchbacks and crossovers too.
How do you prepare the SUV before mounting the rack?
Wash and dry the contact points, then remove anything that would sit between the rack and the paint. Dirt under a rubber foot acts like sandpaper once the rack carries weight.
Check the hatch for a spoiler, because some trunk racks need clearance above the glass. Park on level ground and set the parking brake.
For a hitch rack, clean the receiver tube with a rag so the drawbar slides in without grit. On a trunk rack, inspect the hatch edges where the strap hooks will attach.
Hooks need a solid metal lip, not plastic trim or glass. Saris designs the Bones EX to fit vehicles with spoilers and says it covers 90% of top-selling vehicles.
Still, look at your own hatch and decide whether the hooks have a safe grip.
How do you install a Saris trunk rack on an SUV?
Set the rack on the hatch, hook the straps to solid metal edges, and tighten until the frame sits firm. Trunk racks like the Saris Bones EX use six straps in most setups: two top, two side and two bottom.
Start with the top straps and keep them slightly loose while you position the rack.
The Bones EX has an arc-based frame that separates the two bikes on different levels. Adjust the arms so the cradles clear the rear window and the spoiler.
Then fit the side and bottom straps, pulling each one evenly. The ratchet straps have integrated caps that hide the strap ends.
Tighten until the rack does not shift when you rock it by hand, but stop before the straps pull on the trim or press hard on glass. Saris lists a capacity of 2 bikes at 35 lb each.

A strap-on trunk rack with an arc frame that separates two bikes and ratchet straps that tighten without tools.
See it on AmazonThe rack weighs 11 lb, so one person can lift it onto an SUV hatch. Its injection-molded arms and legs keep the frame solid, and the rubber feet articulate to protect paint.
A Bike Beam may be needed for bike frames without a horizontal top tube. If your SUV's hatch is tall, stand on a step stool rather than stretching to reach the top straps.
How do you load bikes on a trunk rack?
Hang the bikes by their top tubes and fasten the hold-down straps, keeping the heavier bike closest to the SUV. Set the handlebars so they do not hit the glass.
Run the anti-sway straps from the frame to the rack so the bikes cannot swing into each other. Check that no pedal, brake lever or wheel touches the paint.
Pull each strap snug and tuck the excess under the integrated caps. Load the rack only up to its stated 35 lb per bike limit.
When you are done, rock the rack again and retighten any strap that has gone slack.
How do you install a Saris hitch rack on an SUV?
Slide the rack's drawbar into the receiver, insert the hitch pin, and tighten the anti-wobble hardware. The drawbar should go in fully so the pin hole lines up.
Fit the pin and the clip or lock, then tighten the rack's anti-wobble bolt if it has one.
Some Saris racks use a threaded hitch pin that pulls the drawbar tight against the receiver wall. Check the pin's fit instructions, because a threaded pin is made for specific rack receivers.
If your rack rattles in the hitch, an anti-rattle clamp takes up the play. A hitch rack sits lower and is easier to load than a roof rack.
On an SUV, it also keeps the bikes behind the vehicle instead of above the roof line. Follow the rack's tilt or folding instructions if you need to open the hatch with the rack empty.
How do you stop a hitch rack from rattling?
Use an anti-rattle clamp to remove the play between the drawbar and the receiver. A loose hitch rack wobbles, makes noise and can wear the pin hole over time.
A tightener like the Rhino USA clamp wraps around the receiver and pulls the drawbar against the wall.
The clamp is built for 2-inch hitches and fits Class I to IV receivers. It has a steel core with an electro-galvanized finish and a weatherproof rubberized coating.
Fit it after the hitch pin is in place. Tighten the clamp until the rack stops moving in the receiver.
Check the receiver size before you order, since the 2-inch clamp does not fit a 1 1/4-inch tube.

A 2-inch hitch tightener that pulls the drawbar against the receiver so the rack stops rattling.
See it on AmazonHow do you lock a Saris rack and its bikes?
Fit a locking hitch pin and run a cable through the bike frames. A lock keeps the rack attached to the SUV and the bikes attached to the rack when you stop.
The Swagman locking pin is made for Swagman bike racks and their threaded receiver bars.
It threads into a block inside the drawbar and pulls the rack tight as you turn the key. An 8-foot, 10mm braided steel cable runs through the bike frames and clips to the pin.
The pin is triple chrome plated for rust protection. It fits a 1 1/4-inch hitch, or a 2-inch hitch when the rack uses a 1 1/4-to-2-inch adaptor.
Because the pin is not universal, check that your rack's receiver bar accepts it. Our guide to the bike rack hitch lock covers the lock options in more detail.

A threaded locking hitch pin with an 8 foot cable for racks that use a Swagman-style receiver bar.
See it on AmazonHow tight should the straps and hitch hardware be?
Tight enough to stop movement, not tight enough to bend trim or strip threads. For a trunk rack, rock the frame by hand after each strap and retighten any slack.
The ratchet straps on the Bones EX let you pull evenly without overdoing it.
For a hitch rack, follow the rack's torque guidance for the anti-wobble bolt or threaded pin. A locking pin like the Swagman model should be snug, not forced past its stop.
Check the pin and the clamp again after the first drive, since hardware settles under load. Tighten in small steps and test after each one.
If a strap or bolt will not stay tight, stop and check the fit rather than adding more force.
How do you test the rack before driving?
Load the bikes and drive a short, slow loop, then stop and check every strap, pin and clamp. Push the rack side to side and lift it slightly to look for play.
Shake each bike to confirm the hold-downs are snug. Look for any spot where a bike or the rack touches the paint or glass.
On a trunk rack, retighten the top and bottom straps after the first few miles. On a hitch rack, recheck the hitch pin and the anti-rattle clamp.
Also check that the bikes do not block your lights or plate; add a plate holder or light bar if they do. If anything moves, unload and start the check again before a longer trip.
How do you remove and store a Saris SUV rack?
Unload the bikes first, then loosen the straps or pull the hitch pin, and take the rack off when you are not using it. On a trunk rack, loosen the straps evenly so the frame does not snap back.
Wipe the rubber feet and hooks before storage. On a hitch rack, remove the pin and slide the drawbar out, then store it indoors.
Saris builds the Bones EX from injection-molded parts and 100% recyclable materials. A shaded storage spot keeps sun off the straps.
Inspect the straps and rubber parts each season, and replace any that are frayed or cracked. A stored rack lasts longer and is ready when you next need it.
What should you check before you drive off?
Recheck the fit, the straps and the locks, then load within the stated weight limits. The Bones EX carries 2 bikes at 35 lb each.
A hitch rack should be rated for your bike weights, including any e-bike you carry.
Keep the load balanced and the handlebars clear of the glass. Confirm that no bike blocks your rear lights or plate.
Lock the rack and the bikes if you will stop along the way. If you are switching from a trunk rack to a hitch model, our walkthrough of how to install a Thule bike rack on an SUV covers the same receiver steps for another brand.
Check the straps once more, then start with a slow first mile and stop to confirm the rack has not shifted.
Frequently asked questions
Can a Saris trunk rack go on an SUV with a spoiler?
Saris says the Bones EX fits vehicles with spoilers, and the rack covers 90% of top-selling vehicles. Check your specific model with Saris before you buy, because strap hooks need solid metal edges to grip.
How tight should the rack straps be?
Snug enough that the rack does not shift when you rock it, but not so tight that you pull on trim or glass. Retighten after the first few miles, since straps settle once the rack carries weight.
Is it safe to drive with a trunk rack on a glass hatch?
Follow Saris's strap placement and keep the load within the 35 lb per bike limit. Avoid resting hard parts on glass, and stop to recheck the straps if the rack moves or rattles.
Can I leave a Saris trunk rack on all the time?
Take it off when you are not carrying bikes. Sun and weather wear the straps and rubber feet, and the rack blocks the rear hatch on most SUVs.
Store it indoors and inspect the straps before each trip.
What tools do I need to install a Saris hitch rack?
A hitch rack typically needs a wrench or torque tool for the hitch pin and a rack-specific tool for the tilt or clamp hardware. Trunk racks need no tools beyond your hands, just clean surfaces and the straps.
About this guide: Our look at installing a Saris bike rack on an SUV draws on maker specs, materials and what owners report. See how we research.



